Search:

The first part of the thread deals with what happens when you have 2 ip addresses on the same subnet, that still applies. Go ahead and try the 2 ip addresses, I'll bet out of the box only one will...

With 2 ip addresses you would still need to do something like this: http://justlinux.com/forum/showthread.php?t=84253
Maybe that is all you need, but I don't think so.

You would need to do policy source routing with iproute2. For less problems and a simpler setup, have the 2 lans ip addresses not overlap and split at an subnet boundry point. ie try and hand out...

At the arp layer using ebtables, see: http://ebtables.sourceforge.net/
Drop traffic bound for the macaddress of the adsl modems.
Hope this helps, have fun.

DOMAIN\\user * password *

Is the gernerl layout, so for you try:

VPNlogin\\milen_tihomirov * VPNogin *

What OS is the server running?

If both lans are using 192.168.114.x and none of the addresses overlap, (using dhcp to hand out a different range on each lan) then a simple bridge with 2 nics should do it. The dhcp broadcasts would...

Vectorman has the right idea, but you would need to turn forwarding on in "the box". Next you would need to add a static route on each adsl router(if your router has that ability) to point to the...

http://pptpclient.sourceforge.net/howto-diagnosis.phtml#no_auth_is_possible

Did you setup the pap-secrets file instead of chap-secrets?

Here is the key (peer refused to authenticate). check all the option files in /etc/ppp and check for "auth" in them, if present remove it.

First you need to establish whether the module is present on the hd...
try:
'locate -u' (might take a bit)
'locate velocityget'
No, results found... you need to compile it....
If found, pick...

Hey Joe, there is a couple of things you need to check before you can compile a kernel driver, first the kernel source needs to be installed on your box.

Before you go and try that, could you...

Then just turn off iptables in chkconfig, and place those commands in a file with /sbin/iptables before the -A, set the permissions, and call the script from rc.local.

From a command prompt, does this work?
/sbin/iptables -A INPUT -i eth0 -p tcp --dport 25 -j ACCEPT

Did you recompile your kernel? If you did, can you post the .config file? Did you recompile...

use /etc/ppp/ip-up to call the firewall script, see man pppd

Did you install the "Protocol definitions" package also?
http://sourceforge.net/project/showfiles.php?group_id=80085

OK your isp is using dhcp, dhcp should set the resolv.conf file for you, so you need to start your dhcp client to get an ip.
Try:
/sbin/dhclient eth0
or:
/sbin/dhcpd eth0

How to get...

Check out this thread:

http://justlinux.com/forum/showthread.php?t=140010

On the xbox do a `route -n` is there a default gateway set?

The problem is the prerouting chain is seen before the filter table, and your prerouting rule has no exception to it.
try
$IPTABLES -t nat -A PREROUTING -s !<source ip> -d $INET_IP tcp --dport 25...

> 10: 53792 IO-APIC-level uhci_hcd, uhci_hcd, uhci_hcd
I think, that might be your add on card usb card.
what doe 'lspci' output?
I'd, try swapping the usb and nic card around, the nic might end...

19: 41045 IO-APIC-level ohci_hcd, eth0

Think that is a usb2 controller.
What kind of usb stuff do you have connected?

post the output of '/sbin/lspci'

Have you tried booting with "noapic"?
to do so edit grub.conf:
adding "noapic" to the append line.

"MII PHY found at address 1" and "no MII interfaces found" is a bit strange.
Can you get the exact chipset number for the nic, or a link to the motherboard?

Sounds like a nic driver issue to me, what is the nic? is it sharing a irq? if so, with what?

Can you post make and model of the modem and the output of "/sbin/mii-tool -vv". On a hunch only, you may need to use a cross-over cable from the nic card to the modem.