-
Cycling video settings
When I press ctrl + alt + "+" or "-" to cycle through video settings, nothing happens. I have my XF86Config-4 file set up to 1280x1024 for all 3 settings because i was stuck on 800x600 and couldn't change from it (even though i had 1280x1024 for one of the settings). I have Red Hat 7.2 and have a geforce2mx 400. When I attempt to run Xconfigurator, it rewrites the file and 'X' doesn't even work. I have to modify it through pico to work again. Any suggestions?
-
If i'm understanding you correctly then you need to have multiple entries to switch between
eg:
Modes "1280x19242 "1024x768" "800x600"
Then when you do the Ctrl Alt plus or minus thingy....it will switch between the modes you defined above.
Hope this helps
-
i do have multiple entries
-
As in the Screen section and Modelines?
Code:
Section "Modes"
Identifier "Modes[0]"
Modeline "800x600" 37.44 800 816 928 1072 600 600 605 626
Modeline "800x600" 43.68 800 816 928 1072 600 600 606 626
Modeline "800x600" 49.92 800 816 928 1072 600 600 607 626
Modeline "800x600" 56.16 800 816 928 1072 600 600 608 626
Modeline "800x600" 62.40 800 816 928 1112 600 600 609 626
Modeline "800x600" 68.64 800 816 928 1112 600 600 616 626
Modeline "800x600" 74.88 800 816 928 1112 600 600 616 626
ModeLine "1800x1440" 250.00 1800 1896 2088 2392 1440 1441 1444 1490
Modeline "1800x1440" 235.47 1800 1944 2352 2416 1440 1440 1456 1504
Modeline "1800x1440" 249.95 1800 1944 2352 2416 1440 1440 1456 1504
Modeline "1600x1200" 149.76 1600 1616 1968 2208 1200 1200 1211 1253
Modeline "1600x1200" 174.72 1600 1616 1968 2208 1200 1200 1213 1253
Modeline "1600x1200" 199.68 1600 1616 1968 2208 1200 1200 1215 1253
Modeline "1600x1200" 222.56 1600 1616 1968 2208 1200 1200 1216 1253
Modeline "1600x1200" 224.64 1600 1616 1968 2208 1200 1200 1216 1253
Modeline "1600x1200" 249.60 1600 1616 1968 2280 1200 1200 1218 1253
Modeline "1280x1024" 102.24 1280 1296 1552 1736 1024 1024 1033 1070
Modeline "1280x1024" 119.28 1280 1296 1552 1736 1024 1024 1035 1070
Modeline "1280x1024" 136.31 1280 1296 1552 1736 1024 1024 1036 1070
Modeline "1280x1024" 153.35 1280 1296 1552 1736 1024 1024 1039 1070
Modeline "1280x1024" 170.39 1280 1296 1552 1736 1024 1024 1040 1070
Modeline "1280x1024" 178.05 1280 1296 1552 1736 1024 1024 1040 1070
Modeline "1024x768" 61.19 1024 1040 1216 1400 768 768 775 802
Modeline "1024x768" 71.39 1024 1040 1216 1400 768 768 776 802
Modeline "1024x768" 81.59 1024 1040 1216 1400 768 768 777 802
Modeline "1024x768" 91.79 1024 1040 1216 1400 768 768 778 802
Modeline "1024x768" 101.99 1024 1040 1216 1400 768 768 779 802
Modeline "1024x768" 112.19 1024 1040 1216 1400 768 768 784 802
Modeline "1024x768" 122.39 1024 1040 1216 1400 768 768 784 802
Modeline "640x480" 23.96 640 656 720 864 480 480 484 501
Modeline "640x480" 27.96 640 656 720 864 480 480 485 501
Modeline "640x480" 31.95 640 656 720 864 480 480 485 501
Modeline "640x480" 35.94 640 656 720 864 480 480 486 501
Modeline "640x480" 39.94 640 656 720 864 480 480 487 501
Modeline "640x480" 43.93 640 656 720 864 480 480 491 501
Modeline "640x480" 47.92 640 656 720 864 480 480 491 501
EndSection
Section "Screen"
DefaultDepth 16
SubSection "Display"
Depth 15
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 16
Modes "1800x1440" "1600x1200" "1280x1024" "1024x768" "800x600" "640x480"
EndSubSection
SubSection "Display"
Depth 24
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 32
Modes "800x600"
EndSubSection
SubSection "Display"
Depth 8
Modes "800x600"
EndSubSection
Device "Device[0]"
Identifier "Screen[0]"
Monitor "Monitor[0]"
EndSection
-
i don't have any "modes" listed. what do the numbers after the resolution represent?
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
|
|